Special socket wrenches

Lock nut socket wrench, KM2

Specialized tool that is designed to fit the specific dimensions of the KM2 lock nut, allowing for precise and efficient tightening or loosening.

Taillight nut wrench for Tesla

Tail light nut wrench for Tesla vehicles. Specifically designed for quick and easy removal and installation of taillight nuts in Tesla models.

Lock nut socket wrench, KM3

Outer diameter: 32mm, inner diameter: 25mm, teeth: 3.6mm, length 45mm.

Tesla battery cover screw socket, 5-teeth

This is a specialized 5-angle tooth wrench for removing and reinstalling Tesla battery compartment cover screws.

Impact bit set, 9pcs

A 9-piece impact bit set designed for both manual and impact wrenches, featuring Spline (Ribe) bits from T20 to T70, compatible with 1/2" drives.

Extra deep socket set 12pt, 15-19mm

A 5-piece extra deep socket set with 12-point design, covering sizes from 15mm to 19mm, ideal for accessing recessed fasteners and providing secure grip. 1/2" drive.

Front hub nut wrench for Iveco Daily (2004-2019)

Front hub nut wrench for Iveco Daily (2004-2019).

Lock nut socket wrench, KM 4, 28.3mm, 4 teeths

Socket wrench for bearing nuts, KM 4, 28.3mm, 4 teeths, hex drive.

Extra deep socket set 12pt, 8-14mm

Extra deep socket set, 12pt, sizes 8-14mm. Includes 8mm, 10mm, 12mm, 13mm, 14mm for extended reach in tight spaces.

Special socket set for A/C and ECU repair

For special safety screws. Suitable for A/C units for MAFs, for ECUs, for the injector air supply, for mass sensors.

1/2" Special socket wrench set for passenger cars

A versatile 1/2" drive socket set, featuring 6-point, 3-point, 10-point, and pentagon sockets for a variety of automotive tasks, including Toyota idler gear fixings, Nissan and Renault clutches, Honda Civic control arms, and more.

Product code: MG93289

Stud extractor, 1/4"-3/4"

A stud driver (also known as a stud puller) is a tool that is commonly used in automotive repair when a stud is stuck or cracked in the vehicle's chassis or other structural component.

Product code: MG50047

Wrench for Iveco 35 front wheel hub nuts

This wrench is specifically designed to fit front wheel hub nuts with internal teeth and M50*1.5 thread dimensions.

Product code: W0664

Wrench for the front swingarm pivot pin caps on Citroen, Peugeot, Toyota

Socket wrench for the front swingarm pivot pin caps on Citroen (Jumpy, SpaceTourer), Peugeot (Expert, Traveller), Toyota (Proace) suspensions. 2016 and on.

Product code: W0577

Front axle hub socket wrench for Suzuki Jimny, Vitara, Grand Vitara

Front axle hub socket wrench for Suzuki Jimny, Vitara, Grand Vitara. Diameter: 56mm, hexagonal drive.

Product code: W0562

Socket wrench for lock nuts, KM14

Designed for safe and easy tightening and loosening of lock nuts.

Product code: W0694

Lock nut socket wrench KM13 for bearing nuts

Lock nut socket wrench KM13, 6 teeth, thread: M65 x 2, internal teeth.

Product code: W0648

Lock nut wrench for KM16 locknuts

Lock nut wrench for KM16 locknuts. O.D.: 109mm. I.D.: 97.6mm.

Product code: W0624

Bearing nut socket wrench, KM5, 44.3mm

These wrenches are used to tighten the nuts that attach the axles to the wheels of the car. The keys ensure that the axles are properly attached to the wheels and allow maintenance work to be carried out.

Product code: W0568

Lock nut socket wrench, grooved, KM7

Lock nut socket wrench, grooved, KM7.